新聞資訊
ZX115鎂合金熱壓縮過程的本構分析及有限元模擬
發布人：上海艾荔艾金屬材料有限公司www.85978597.cn
更新時間：2015-09-16
在應變速率為1×10-3~1 s-1、溫度為300~450 ℃條件下，采用Gleeble-3500型熱模擬機對Mg-1.3Zn-1.7Ca (質量分?jǐn)?shù)，%)鎂合金(ZX115)進行單軸熱壓縮實驗；通過分析ZX115鎂合金的真應力-真應變曲線，探討變形溫度和應變速率對其流變曲線中峰值應力、峰值應變及Zener-Hollomom參數的影響，建立描述該合金高溫壓縮變形的本構方程。將本構方程應用于有限元分析軟件 DEFORM 3D中，并對ZX115鎂合金熱壓縮過程進行數值模擬，利用后處理程序，分析工件內部的應變速
ZX115鎂合金熱壓縮過程的本構分析及有限元模擬Constitutive analysis and FEM simulation of hot compression of ZX115 magnesium alloy
在應變速率為1×10-3~1 s-1、溫度為300~450 ℃條件下，采用Gleeble-3500型熱模擬機對Mg-1.3Zn-1.7Ca (質量分?jǐn)?shù)，%)鎂合金(ZX115)進行單軸熱壓縮實驗；通過分析ZX115鎂合金的真應力-真應變曲線，探討變形溫度和應變速率對其流變曲線中峰值應力、峰值應變及Zener-Hollomom參數的影響，建立描述該合金高溫壓縮變形的本構方程。將本構方程應用于有限元分析軟件 DEFORM 3D中，并對ZX115鎂合金熱壓縮過程進行數值模擬，利用后處理程序，分析工件內部的應變速率場、應變場和溫度場變化。研究表明：溫度越高或應變速率越低時，流變曲線所達到的峰值應力越小，而在相同的應變速率下，峰值應變也隨著變形溫度的升高而明顯減小；ZX115合金熱壓縮過程具有明顯的變形不均勻性，為了合理控制變形后的再結晶晶粒尺寸，可適當降低形變溫度和應變速率。
The hot compressions of Mg-1.3Zn-1.7Ca (mass fraction, %)magnesium alloy (ZX115) were carried out on Gleeble-3500 thermal simulator at a strain rate of 1×10-3-1 s-1?and temperature range of 300-450 ℃. Based on the true stress-strain curves of ZX115 magnesium alloy obtained from experiments, the effects of deformation temperatures and strain rates on the peak stress, peak strain and Zener-Hollomon parameter were discussed, and the constitutive equations were established to describe the hot compression of ZX115 magnesium alloy. These constitutive equations were applied into finite element analysis software DEFORM 3D and then the hot compressions of ZX115 magnesium alloy were simulated. The variation and distribution of strain rate, strain and temperature in the compressed workpiece were analyzed by the post-processing procedures. The results show that peak stress decreases with increasing the deformation temperature or decreasing the strain rate, and the peak strain decreases with increasing the temperature under a given strain rate. The hot compressions of ZX115 magnesium alloy exhibits a nonuniform characteristic. In order to control the recrystallized grain size, the deformation temperature and strain rate should be necessarily decreased.
以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.85978597.cn，轉載請注明出處。
前一頁：冷熱循環處理對6005A鋁合金焊接接頭顯微組織和力學性能的影響
后一頁：Al-Cu-Li-Mg-Mn-Zn-Ag合金的熱變形流變行為與本構方程