新聞資訊
基于非線性超聲調制頻譜識別2024-T351鋁合金板材的疲勞裂紋
發布人：上海艾荔艾金屬材料有限公司www.85978597.cn
更新時間：2015-11-23
基于非線性超聲調制頻譜法，對航空鋁合金板材中的疲勞裂紋識別進行研究；以兩個不同頻率的超聲蘭姆波為激勵信號，依靠超聲換能器、波形發生器和激光測振儀等，對含有疲勞裂紋和無損傷的2024-T351鋁合金薄板試樣進行對比實驗；分別采用時域、頻域和時頻域聯合法分析非線性超聲波在鋁合金薄板試樣中傳播的響應信號。
基于非線性超聲調制頻譜識別2024-T351鋁合金板材的疲勞裂紋Identification of fatigue cracks in 2024-T351 aluminum alloy plates based on nonlinear ultrasonic modulation spectrum
基于非線性超聲調制頻譜法，對航空鋁合金板材中的疲勞裂紋識別進行研究；以兩個不同頻率的超聲蘭姆波為激勵信號，依靠超聲換能器、波形發生器和激光測振儀等，對含有疲勞裂紋和無損傷的2024-T351鋁合金薄板試樣進行對比實驗；分別采用時域、頻域和時頻域聯合法分析非線性超聲波在鋁合金薄板試樣中傳播的響應信號。結果表明：非線性聲學特征即調制頻譜及三階諧波可作為識別2024-T351鋁合金板材介質中疲勞裂紋的判據，通過對試樣表面進行掃描，建立調制頻譜的峰值幅度與位移的關系，據此可確定樣板中疲勞裂紋的位置和輪廓，這為航空鋁合金板材疲勞裂紋的識別提供更多技術支撐。
The identification of fatigue cracks in the aviation aluminum alloy plates based on nonlinear ultrasonic modulation spectrum method was studied. Taking two different frequencies nonlinear Lamb wave as actuators, comparative experiments on two types of 2024-T351 aluminum alloy plate samples, with and without fatigue crack, were performed by using ultrasonic transducer, waveform generator and non-contact laser vibration meter and so on. The ultrasonic response signals during propagation were analyzed by the time domain, frequency domain and time-frequency domain methods, respectively. The results show that the acoustic characteristic of the modulation frequency components and the third harmonics can be used to indicate the presence of fatigue cracks in 2024-T351 aluminum alloy plates. By scanning the cracked plate, a relationship between the modulation frequency peak magnitude and scanning displacement was established, and according to this relationship the fatigue cracks can be located approximately, the crack contour can be obtained, which will provide more technical support for identification fatigue cracks in aviation aluminum alloy plate.
?以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.85978597.cn，轉載請注明出處。