新聞資訊
基于應變影響的7A09鋁合金等溫壓縮流動應力模型
發布人：上海艾荔艾金屬材料有限公司www.85978597.cn
更新時間：2015-11-27
在Gleeble?1500型熱模擬壓縮機上研究7A09鋁合金在溫度為633 ~733 K、應變速率為0.01~10.0 s?1、最大變形程度為60%條件下的高溫流動行為；基于7A09鋁合金高溫壓縮時的流動應力特征，建立反映應變影響的7A09鋁合金流動應力模型。
基于應變影響的7A09鋁合金等溫壓縮流動應力模型Flow stress model considering contribution of strain in?isothermal compression of 7A09 aluminum alloy
在Gleeble?1500型熱模擬壓縮機上研究7A09鋁合金在溫度為633 ~733 K、應變速率為0.01~10.0 s?1、最大變形程度為60%條件下的高溫流動行為；基于7A09鋁合金高溫壓縮時的流動應力特征，建立反映應變影響的7A09鋁合金流動應力模型。結果表明：隨著變形溫度的升高和應變速率的降低，合金的流動應力顯著降低；當應變超過一定值后，隨著應變的增加，高、低應變速率下合金的流動應力變化趨勢不同；建立的流動應力模型的計算值與實驗值之間的最大誤差為7.77%，平均誤差為2.69%；與不考慮應變影響的流動應力模型相比，該模型的擬合精度高，能較好地描述7A09鋁合金高溫變形過程中的流動行為，為鋁合金高溫變形過程的數值模擬奠定了較好的基礎。
The flow behavior of isothermally compressed 7A09 aluminum alloy in the deformation temperature range from 633 to 733 K, the strain rate range from 0.01 to 10.0 s?1?and the maximum deformation of 60% was investigated on a Gleeble?1500 isothermal compressor. Meanwhile, a flow stress model considering the contribution of the strain was established in the isothermal compression of 7A09 aluminum alloy. The results show that the flow stress of 7A09 aluminum alloy significantly decreases with the increase of the deformation temperature and the decrease of strain rate. After a critical value of strain, the flow stress changes differently with the increase of the strain at higher and lower strain rates. The maximum and the average differences between the calculated flow stress by the flow stress model and the experimental ones are 7.77% and 2.69%, respectively. The comparison between the present flow stress model and that without considering the strain shows that the present flow stress model has higher precision and can efficiently predict the flow behavior in the isothermal compression of 7A09 aluminum alloy. The present flow stress model is also beneficial to the FEM simulation of thermal deformation for 7A09 aluminum alloy.
?以上資料由上海艾荔艾金屬材料有限公司提供，歡迎新老客戶來電洽購。
本文來自上海艾荔艾金屬材料有限公司http://www.85978597.cn，轉載請注明出處。